龙丘MC9S12X多功能开发板V1.0
Designed by 龙丘
E-mail:chiusir@163.com
软件版本:V1.1
最后更新:2009年2月21日
相关信息参考下列地址：
博客： http://longqiu.21ic.org
淘宝店：http://shop36265907.taobao.com
------------------------------------
Code Warrior 4.7
Target : MC9S12XS128
Crystal: 16.000Mhz
busclock:16.000MHz
pllclock:32.000MHz
============================================
演示程序使用说明：
1.串口9600bps，中断显示
2.PWM波形测试，测试方法：
按u:增加频率
按d:降低频率
按l:减小占空比
按r:增加占空比
按o:开启声音
按c:关闭声音
*****************************************************************************************/
#include <hidef.h> /* common defines and macros */
#include <MC9S12XS128.h>
#include <stdio.h>
#pragma LINK_INFO DERIVATIVE "mc9s12xs128"
byte u8_RCV_Ch=0xff;
//====================中断函数==================================
#pragma CODE_SEG DEFAULT
void Dly_ms(int ms)
{
int ii,jj;
if (ms<1) ms=1;
for(ii=0;ii<ms;ii++)
for(jj=0;jj<2770;jj++); //32MHz--1ms
}
//-----------------------------------------------------
static void SCI_Init(void)
{
SCI0CR2=0x2c; //enable Receive Full Interrupt,RX enable,Tx enable
SCI0BDH=0x00; //busclk 8MHz,19200bps,SCI0BDL=0x1a
SCI0BDL=0x68; //SCI0BDL=busclk/(16*SCI0BDL)
//busclk 16MHz, 9600bps,SCI0BDL=0x68
}
void uart_putchar(unsigned char ch)
{
if (ch == '\n')
{
while(!(SCI0SR1&0x80)) ;
SCI0DRL= 0x0d; //output'CR'
return;
}
while(!(SCI0SR1&0x80)) ; //keep waiting when not empty
SCI0DRL=ch;
}
void putstr(char ch[])
{
unsigned char ptr=0;
while(ch[ptr]){
uart_putchar((unsigned char)ch[ptr++]);
}
}
unsigned char uart_getkey(void)
{
byte res=0;
while(!(SCI0SR1&0x80)) ; //keep waiting when not empty
return (SCI0DRL);
}
//-----------------------------------------------------
static void Port_Init(void)
{
DDRB = 0xff; //LED PTB0--7,
PORTB= 0xff; //LEDs on
}
// PLL初始化子程序 BUS Clock=16M
void setbusclock(void)
{
CLKSEL=0X00; //disengage PLL to system
PLLCTL_PLLON=1; //turn on PLL
SYNR=1;
REFDV=1; //pllclock=2*osc*(1+SYNR)/(1+REFDV)=32MHz;
_asm(nop); //BUS CLOCK=16M
_asm(nop);
while(!(CRGFLG_LOCK==1)); //when pll is steady ,then use it;
CLKSEL_PLLSEL =1; //engage PLL to system;
}
//-----------------------------------------------------
static void PWM_Init(void)
{
//SB,B for ch2367
//SA,A for ch0145
PWMPRCLK = 0X55; //clockA,CLK B 32分频:500khz
PWMSCLA = 0x02; //对clock SA 进行2*PWMSCLA=4分频；pwm clock=clockA/4=125KHz;
PWMSCLB = 0X02; //clk SB=clk B/(2*pwmsclb)=125KHZ
//pwm1
PWMCNT1 = 0;
PWMCAE_CAE1=0;
PWMPOL_PPOL1=0;
PWMPER1 =125;
PWMDTY1 =100;
PWMCLK_PCLK1 = 1;
PWME_PWME1 = 0;
}
//-----------------------------------------------------
void Init_Dev(void)
{
setbusclock();
Port_Init();
SCI_Init();
PWM_Init();
}
//-----------------------------------------------------
void Beep(void)
{
word tmper=125,ty=100;
tmper=PWMPER1;
ty=PWMDTY1;
PWME_PWME1 = 1;
PWMPER1 =125;
PWMDTY1 =100;
Dly_ms(40);
PWMPER1 =tmper;
PWMDTY1 =ty;
PWME_PWME1 = 0;
}
#pragma CODE_SEG __NEAR_SEG NON_BANKED
void interrupt 20 SCI0_ISR(void)
{
SCI0CR2_RIE=0;
//此处为串口中断需要处理的事情
uart_putchar(u8_RCV_Ch=uart_getkey());
//PORTA_PA0=~PORTA_PA0;
PORTB_PB7=~PORTB_PB7;
switch(u8_RCV_Ch)
{
case 'u':
u8_RCV_Ch=0xff;
PWME_PWME1 = 1; //开启PWM0波形输出
if(PWMPER1>15) //增大频率
PWMPER1-=5;
break;
case 'd':
u8_RCV_Ch=0xff;
PWME_PWME1 = 1;
if(PWMPER1<255) //减小频率
PWMPER1++;
if(PWMDTY1>
WMPER1+10) //减小占空比PWMDTY1=PWMPER1*4/5; //20%
break;
case 'l':
u8_RCV_Ch=0xff;
PWME_PWME1 = 1;
if(PWMDTY1<;PWMPER1) //增大占空比
PWMDTY1++;
break;
case 'r':
u8_RCV_Ch=0xff;
PWME_PWME1 = 1;
if(PWMDTY1<;PWMPER1) //减小占空比
PWMDTY1--;
break;
default:
break;
}//switch(u8_RCV_Ch)
//Beep();
SCI0CR2_RIE = 1;
}
//====================main()==================================
#pragma CODE_SEG DEFAULT
void main(void)
{
char txtbuf[16]="";
Init_Dev();
PORTB=0x00;
putstr("\nLongQiu s.&t. Co. Ltd.");
putstr("\nhttp://shop36265907.taobao.com");
Dly_ms(1000);
PORTB=0xFF;
EnableInterrupts;
for(;;)
{
Dly_ms(500);
//----------PWM0----------------------------------
sprintf(txtbuf,"\nFrequence: %d0Hz",PWMPER1);
putstr(txtbuf);
sprintf(txtbuf,"\n duty circle: %d%%",(PWMPER1-PWMDTY1)*100/PWMDTY1);
putstr(txtbuf);
PORTB_PB0=~PORTB_PB0;
}//for(;;)
} //main