智能车制作

标题: 龙丘智能奉献LCD1602液晶MC9S12XS128代码一份，接口说明详细 [打印本页]

作者: chiusir 时间: 2010-12-8 21:24
标题: 龙丘智能奉献LCD1602液晶MC9S12XS128代码一份，接口说明详细
Code Warrior 5.0
Target : MC9S12XS128
Crystal: 16.000Mhz
busclock: 8.000MHz
pllclock:16.000MHz
============================================
液晶管脚接线定义
PIN1 GND
PIN2 5V
PIN3 10K电阻接地
PIN4 LCD1602_RS PORTB_PB0 //Data Command Pin  1 data  0 command
PIN5 LCD1602_RW PORTB_PB1 //Read Write Pin 1 read 0 write
PIN6 LCD1602_EN PORTB_PB2 //LCD Enable Signal
PIN7-14 LCDIO    PORTA
------------------------------------------------------
主题函数如下图，完整工程参考附件：[attach]4254[/attach]
#include "derivative.h"
#include "LQ1602.h"
void LcdInit(){
  DDRA = 0xff;
  DDRB = 0xff;
  LCDIO_DIR = LCDIO_DIR_OUT;
LcdDelay();
LcdCommand(CLR,0);       //clear screen
LcdCommand(DATA_MODE,1); //set 8 bit data transmission mode
LcdCommand(INPUTMODE_CUR_R | INPUTMODE_ALL_D, 1); // cursor right, disable moving
LcdCommand(SCREEN_OPEN | SCREEN_OPEN_CUR | SCREEN_OPEN_TWI, 1); //open display (enable lcd display)
LcdCommand(LINE1_HEAD,1); //set lcd first display address
LcdCommand(CLR,1);       //clear screen
}
////////////////////////////////////////////////////////////////////
// write command function
//
void LcdCommand(byte command,byte BusyC){
if (BusyC) ReadStatus(); //Test it busy or not
LCDIO=command;
LCD1602_RS=0;
LCD1602_RW=0;
LCD1602_EN=0;
LCD1602_EN=0;
LCD1602_EN=1;
}
byte ReadStatus(void)
{
  byte cRtn;
LCDIO_DIR = LCDIO_DIR_IN;
LCD1602_RS = 0;
LCD1602_RW = 1;
LCD1602_EN = 0;
LCD1602_EN = 0;
LCD1602_EN = 1;
while (LCDIO & BUSY); //Test Busy State
cRtn = LCDIO_DIR;    // if Not save the port value, it should be change
LCDIO_DIR = LCDIO_DIR_OUT;
return(cRtn);
}
void LcdDelay(void)
{
  word i, j;
  for (i = 0; i < 300; i++)
for(j = 0; j < 3000; j++);
}
void LcdClear(void)
{
  LcdCommand(CLR,1);       //clear screen
}
////////////////////////////////////////////////////////////////////
// write data function
//
void LcdData(byte dat,byte BusyC)
{
if (BusyC) ReadStatus(); //Test it busy or not
LCDIO=dat;
LCD1602_RS=1;
LCD1602_RW=0;
LCD1602_EN=0;
LCD1602_EN=0;
LCD1602_EN=1;
}
////////////////////////////////////////////////////////////////////
// write lcd a character function
//
void LcdWriteChar( byte x,byte y,byte dat){
  LcdSetXY(x, y);
LcdData(dat,1);
}
////////////////////////////////////////////////////////////////////
// set display address function
//
void LcdSetXY( byte x, byte y ){
byte address;
if (y == LINE1)
address = LINE1_HEAD + x;
else
address = LINE2_HEAD + x;
LcdCommand(address,1);
}
////////////////////////////////////////////////////////////////////
// write lcd string function
//
void LcdWriteStr(byte X,byte Y,char *s)
{
LcdSetXY( X, Y ); //set address
while (*s)  // write character
{
   LcdData(*s, 1);
   s++;
}
}

欢迎光临智能车制作 (http://111.231.132.190/)